Merci de la réponse.
J'ai essayé de recharger le logiciel sur un autre ordinateur. Pas de problème pour la compilation. Par contre lors du versement, j'ai le message suivant :
* Exécution de la tâche dans le dossier CommandStation-EX-LaBox : platformio run --target upload --environment ESP32
Processing ESP32 (platform: espressif32; board: esp32doit-devkit-v1; framework: arduino)
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Verbose mode can be enabled via `-v, --verbose` option
CONFIGURATION: https://docs.platformio.org/page/boards/espressif32/esp32doit-devkit-v1.html
PLATFORM: Espressif 32 (6.10.0) > DOIT ESP32 DEVKIT V1
HARDWARE: ESP32 240MHz, 320KB RAM, 4MB Flash
DEBUG: Current (cmsis-dap) External (cmsis-dap, esp-bridge, esp-prog, iot-bus-jtag, jlink, minimodule, olimex-arm-usb-ocd, olimex-arm-usb-ocd-h, olimex-arm-usb-tiny-h, olimex-jtag-tiny, tumpa)
PACKAGES:
- framework-arduinoespressif32 @ 3.20017.241212+sha.dcc1105b
- tool-esptoolpy @ 1.40501.0 (4.5.1)
- tool-mkfatfs @ 2.0.1
- tool-mklittlefs @ 1.203.210628 (2.3)
- tool-mkspiffs @ 2.230.0 (2.30)
- toolchain-xtensa-esp32 @ 8.4.0+2021r2-patch5
LDF: Library Dependency Finder -> https://bit.ly/configure-pio-ldf
LDF Modes: Finder ~ chain, Compatibility ~ soft
Found 38 compatible libraries
Scanning dependencies...
Dependency Graph
|-- OneButton @ 2.6.1
|-- Adafruit GFX Library @ 1.11.11
|-- Adafruit SSD1306 @ 2.5.13
|-- ACAN_ESP32 @ 1.1.2
|-- EEPROM @ 2.0.0
|-- BluetoothSerial @ 2.0.0
|-- ESPmDNS @ 2.0.0
|-- WiFi @ 2.0.0
|-- Wire @ 2.0.0
|-- Adafruit BusIO @ 1.17.0
|-- SPI @ 2.0.0
Building in release mode
Retrieving maximum program size .pio/build/ESP32/firmware.elf
Checking size .pio/build/ESP32/firmware.elf
Advanced Memory Usage is available via "PlatformIO Home > Project Inspect"
RAM: [== ] 15.7% (used 51296 bytes from 327680 bytes)
Flash: [======= ] 73.2% (used 959157 bytes from 1310720 bytes)
Configuring upload protocol...
AVAILABLE: cmsis-dap, esp-bridge, esp-prog, espota, esptool, iot-bus-jtag, jlink, minimodule, olimex-arm-usb-ocd, olimex-arm-usb-ocd-h, olimex-arm-usb-tiny-h, olimex-jtag-tiny, tumpa
CURRENT: upload_protocol = esptool
Looking for upload port...
Auto-detected: /dev/ttyUSB0
Uploading .pio/build/ESP32/firmware.bin
esptool.py v4.5.1
Serial port /dev/ttyUSB0
Connecting...................
Chip is ESP32-D0WD-V3 (revision v3.1)
Features: WiFi, BT, Dual Core, 240MHz, VRef calibration in efuse, Coding Scheme None
WARNING: Detected crystal freq 15.67MHz is quite different to normalized freq 26MHz. Unsupported crystal in use?
Crystal is 26MHz
MAC: d4:8a:fc:c8:bf:bc
Uploading stub...
A fatal error occurred: Serial data stream stopped: Possible serial noise or corruption.
Salut Jean-Paul,
tu peux mettre tout ton code (Tout le dossier PlateformIO devrais-je dire) en PJ je vais regarder ça sur PlatformIO !!!
Christophe
